Making beautiful and professional looking cabinet doors is easy! Our cutters can be used to make square edge or arch cathedral pattern doors without the need for a fence. Bits can be converted to make beautiful glass door or picture frames from 5/8" to 1" thick without the need for additional cutters. You can also flip your stock over to create up to 1-3/8" double passage interior doors. All bits two flute, carbide tipped, 1/2" shank with ball bearing guides and cut a standard 1/4" x 3/8" thick tongue. Use in router table only. Instructions included. USA

Plywood Stile and Rail Sets: Ready to use sets for 1/4" flat plywood panels (7/32" or 5.5 mm). Conversion kit not required.

Miniature 2-Piece Stile and Rail Bit Sets: (185-0710, 185-0810) Make doors as small as 2" square from 3/8" to 3/4" thick with our reduced profile Stile and Rail and Panel bits. The panel groove measures 5/32" thick by 1/4"deep. Setup Kwik Blocks and Door templates are also available. All bits 1/2" shank, two flute and carbide tipped with ball bearing guides. USA

brand - click here
What's the difference?

(3 Customer Reviews)    Write your own review

---

Product Rating:     Date Posted: 2008-02-22 00:00:00

Pricey but worth it!!!

Posted By: Eric Long

Location: Lewiston, ME United States

Comments: Excellent set of rail and stile bits. Razor sharp and set perfectly. They are very good bit and I would highly recommend them to anyone.

Product Rating:     Date Posted: 2008-03-20 00:00:00

Clean Cuts

Posted By: Wayne

Location: Fort Worth, TX United States

Comments: Been using these stile and rail bits for a while now and with the set up blocks I get clean cuts with perfect fits every time.

Product Rating:     Date Posted: 2011-02-21 21:59:12

Great bits!

Posted By: Jeff

Location: Decatur, , IL United States

Comments: I purchased 20 degree stile and rail set and the matching set up blocks and I could not be happier. Perfect set up right out of the box. The first set of doors I built were awesome. Looking forward to using them again. I did a lot of research before I made the purchase I was pleased with the price and quality. They are made in the USA so what more could you ask for!

Product Instructions:

Reversible Stile & Rail

Router Saftey Chart - Suggested Speeds:

Bit Diameter	Max Speed
up to 1"	24000 RPM
1-1/16" to 2"	18000 RPM
2-1/16" to 2-1/2"	16000 RPM
2-9/16" to 3"	14500 RPM
over 3"	12000 RPM

Router Saftey Tips:

• Always wear eye and ear protection.
• Always use properly sharpened bits.
• Never use bits that are dull or damaged.
• Shank must be completely inserted into collet and then backed-off approximately 1/16".
• Don't "bottom-out" bit in collet.
• Never partially insert bit into collet. Tighten securely and recheck periodically for possible slippage or "run-out" due to wear.
• Keep collet clean and replace if worn.
• Never start the router with the bit in contact with wood.
• Always feed your work in the proper direction against the bit rotation.
• Don't force feed the bit or overload your router, Feed at a constant moving speed to avoid burning the wood.
• Do not face tool's discharge when operating.
• Always unplug router when changing bits or making adjustments.
• Use a router table and fence whenever possible.
• Make sure your work piece is properly secured and use push blocks, sticks and featherboards whenever possible.
• Keep all your bits, bearings and assemblies clean, lubricated, and securely fastened. To avoid damage, store them properly in a pouch, box or tray.
• The bigger the bit, the lower RPM recommended (see chart).