Solid Carbide Spiral Bit Sets by EAGLE

Clean cutting!

See Options Below

COMBO PACKAGE! SAVE $42!

Shop with Confidence. Our GUARANTEE.

Full Description Below...

Our production quality spiral bits combine effective chip removal with a continuous shearing action cut not obtained from a standard straight bit. You'll get smoother cutting action with better results. All bits are two-flute, solid carbide. USA

Up-cut Bits provide faster cutting while they pull chips up and out of the work or towards the router. They are excellent bits to use when cutting material in a table mounted router. They hold the work piece to the router. Ideal for mortise and tenon, grooving, slotting or routing deep blind holes.

Down-cut Bits cut slower and push chips away from the router to eliminate top surface splintering. Use for pattern cutting or when going completely through the board as it allows clear vision of the cutting line. Ideal for fine finish work such as veneers, laminates, inlays and repairs because they prevent upper edge tear outs. Use Down-cuts for trimming and sizing.

Spiral Flush Trim Bits have double bearing guides and a specially designed glue reservoir that eliminates glue buildup on ball bearings, resulting in a smoother cut and improved production results. Bits last up to 3 times longer than standard flush trim bits. Bearings will not stop or burn the material.

5-Piece Multi-Purpose Solid Carbide Set Special #100-5053:

Includes the following production-quality Eagle America Solid Carbide Router Bits:

  • #106-0412 Spiral Upcut: 1/4" D, 1" Cut Length, 1/4" Shank
  • #106-0615 Spiral Upcut: 3/8" D, 1-1/4" Cut Length, 1/2" Shank
  • #106-0835 Spiral Upcut: 1/2" D, 1-1/2" Cut Length, 1/2" Shank
  • #120-0402 Spiral Flush Trim Upcut: 1/4" D, 1" Cut Length, 1/4" Shank
  • #120-0412 Spiral Flush Trim Downcut: 1/4" D, 1" Cut Length, 1/4" Shank

Regularly $201.75. Combo Package Savings ONLY $159.99--SAVE $42!

3-Piece Solid Carbide Spiral Sets include the following:

Dimensions shown as Diameter x Cutting Length

  • 1/4" Shank: 1/4" x 1"
  • 1/2" Shank: 3/8" x 1-1/4" , 1/2" x 1-1/2"

7-Piece Solid Carbide Spiral Sets include the following:

Dimensions shown as Diameter x Cutting Length

  • 1/4" Shank: 1/8" x 1/2", 5/32" x 9/16", 3/16" x 5/8", 1/4" x 1"
  • 1/2" Shank: 5/16" x 1", 3/8" x 1-1/4", 1/2" x 1-1/2"

4-Piece Metric Up-Cut Solid Carbide Spiral Set includes the following:

Dimensions shown as Diameter x Cutting Length

  • 1/4" Shank: 5mm x 5/8", 6mm x 7/8"
  • 1/2" Shank: 8mm" x 1" , 10mm x 1-1/8"

Router Safety Chart - Suggested Speeds:

Bit Diameter Max Speed
up to 1" 24000 RPM
1-1/16" to 2" 18000 RPM
2-1/16" to 2-1/2" 16000 RPM
2-9/16" to 3" 14500 RPM
over 3" 12000 RPM

Router Safety Tips:

  • Always wear eye and ear protection.
  • Always use properly sharpened bits.
  • Never use bits that are dull or damaged.
  • Shank must be completely inserted into collet and then backed-off approximately 1/16".
  • Don't "bottom-out" bit in collet.
  • Never partially insert bit into collet. Minimum 1" of shank needs to be in collet.
  • Tighten bit securely and recheck periodically for possible slippage or "run-out" due to wear.
  • Keep collet clean and replace if worn.
  • Never start the router with the bit in contact with wood.
  • Always feed your work or router in the proper direction against the bit rotation.
  • Don't force feed the bit or overload your router, Feed at a constant moving speed to avoid burning the wood.
  • Do not face tool's discharge when operating.
  • Always unplug router when changing bits or making adjustments.
  • Use a router table and fence whenever possible.
  • Make sure your work piece is properly secured and use push blocks, sticks and featherboards whenever possible.
  • Keep all your bits, bearings and assemblies clean, lubricated, and securely fastened. To avoid damage, store them properly in a pouch, box or tray.
  • The bigger the bit, the lower RPM recommended (see chart).

Product Options

Description Item # Price    Qty
3 Piece Up-Cut Solid Carbide Spiral Set 100-0615 REG. $121.85
SALE $99.99
SAVE $22!
3 Piece Down-Cut Solid Carbide Spiral Set 199-0625 REG. $121.85
SALE $99.99
SAVE $22!
7 Piece Up-Cut Solid Carbide Spiral Set 100-0675 REG. $224.65
SALE $189.99
SAVE $35!
7 Piece Down-Cut Solid Carbide Spiral Set 100-0685 REG. $224.65
SALE $189.99
SAVE $35!
4 Piece Up-Cut Metric Solid Carbide Spiral Set 199-0640 REG. $133.80
SALE $119.99
COMBO PACKAGE! SAVE $14!
5 Piece Multi-Purpose Solid Carbide Set 100-5053 REG. $201.75
SALE $159.99
SPECIAL! Package Savings! SAVE $42!

You May Also Like

Sign up for our eNewsletter