Free "Best Way" Shipping Every Day in the Contiguous USA!( Shipping Info)

Bottom Cleaning, Surface Planing & Dado Cutting by EAGLE

For a perfect smooth bottom cut - every time!
Review star icon Review star icon Review star icon Review star icon Review star icon 3.5 of 5 Stars (2 reviews)

See Options Below

Shop with Confidence. Our GUARANTEE.

Full Description Below...

Unlike common mortise bits, these bits feature a special overlapping center carbide tip design which guarantees you a smooth and clean bottom cut every time. Ideal for cutting or cleaning out dadoes, cutting stair treads into risers, and putting stress relief on the back of moldings. Special ball bearing allows you to follow deep dado walls or use to follow templates. Great for making wood signs as well as removing paint or varnish.

Great bit for creating"stress relief" areas in backs of large and long trim moldings.
All bits two-flute, carbide-tipped. USA

NOTE: Item numbers ending with B are with bearing

#116-1105 features down shear cutting angle for undersized 3/4" plywood dado cuts.

brand - click here
What's the difference?

Router Safety Chart - Suggested Speeds:

Bit Diameter Max Speed
up to 1" 24000 RPM
1-1/16" to 2" 18000 RPM
2-1/16" to 2-1/2" 16000 RPM
2-9/16" to 3" 14500 RPM
over 3" 12000 RPM

Router Safety Tips:

  • Always wear eye and ear protection.
  • Always use properly sharpened bits.
  • Never use bits that are dull or damaged.
  • Shank must be completely inserted into collet and then backed-off approximately 1/16".
  • Don't "bottom-out" bit in collet.
  • Never partially insert bit into collet. Minimum 1" of shank needs to be in collet.
  • Tighten bit securely and recheck periodically for possible slippage or "run-out" due to wear.
  • Keep collet clean and replace if worn.
  • Never start the router with the bit in contact with wood.
  • Always feed your work or router in the proper direction against the bit rotation.
  • Don't force feed the bit or overload your router, Feed at a constant moving speed to avoid burning the wood.
  • Do not face tool's discharge when operating.
  • Always unplug router when changing bits or making adjustments.
  • Use a router table and fence whenever possible.
  • Make sure your work piece is properly secured and use push blocks, sticks and featherboards whenever possible.
  • Keep all your bits, bearings and assemblies clean, lubricated, and securely fastened. To avoid damage, store them properly in a pouch, box or tray.
  • The bigger the bit, the lower RPM recommended (see chart).
Write a Review

2 reviews
Slightly undersized by ()
Review star icon Review star icon Review star icon Review star icon Review star icon 3 Stars
I'm reviewing the 23/32" bit (116-1105). While a great bit for giving flat bottoms and clean edges, the bit is a little undersized. With a digital caliper, I measured it to 45/64". This makes it too tight for 23/32" plywood dadoes. After routing, I have to sand or plane the sides of the dado, to make the plywood fit.

Great bit for railings by ()
Review star icon Review star icon Review star icon Review star icon Review star icon 4 Stars
I purchased the 1" diameter bit (116-1605) and use it for cutting a groove in custom railings I set on 3/8" x 1" steel bars. It works great on everything from pine to oak, and a couple of exotics my clients have requested. It's not quite up to the challenge of IPE, but I haven't found a bit that is. The groove is super clean and square and is ready to go right off of the router table, no additional work necessary.

Product Options

D
Diameter
L
Length
Overall
Length
Shank
Size
Item # Price    Qty
23/32" 3/8" 2-1/4" 1/2" 116-1105 $31.95
3/4" 3/8" 2-1/4" 1/2" 116-1205 $31.95
3/4" 3/8" 2-1/4" 1/2" 116-1205B $45.95
1" 3/8" 2-1/4" 1/2" 116-1605 $34.95
1" 3/8" 2-1/4" 1/2" 116-1605B $51.95
1-1/2" 5/8" 2-5/8" 1/2" 116-2405 $37.95
1-1/2" 5/8" 2-5/8" 1/2" 116-2405B $57.95
Sign up for our eNewsletter